StockOiler by HENLI Get a quote

Double-sided stock oiler

Both faces of the strip oiled in one pass. No pump, no air, no power.

Working width
65 to 1600 mm
Strip thickness
0.1 to 6.0 mm
Reservoir
4 L, gravity fed

How the CT oiler works

Five parts, and nothing to plug in. Tap a ring to open each one.

Front view of the CT stock oiler: hanging reservoir, ball valve, hose and the roller head with its row of brass valves

01 / 05

4 L hanging reservoir

Translucent, so the oil level is easy to see. It hangs above the roller head and feeds it by gravity.

Capacity
4 L
Power
None needed
The 4 L reservoir hanging by its wire handle, with the brass ball valve underneath

02 / 05

Ball valve

Opens and closes the oil feed under the reservoir. Shut it when the line stops, open it when the line runs.

Operated
By hand
Position
Under the reservoir
Brass ball valve with a red handle under the reservoir, with the hose attached

03 / 05

Brass drip valves

Each brass valve meters the oil for its own section of the roller width. Open only the valves over your strip.

Body
Anodized aluminium
Valves
Brass, micro-adjustable
Brass adjustment valves along the aluminium manifold, with the drip nozzles above the felt roller

04 / 05

Wool felt rollers

The upper felt is wetted from above; oil runs down and wets the lower felt. The strip passes between them and both faces are coated. Excess oil collects in the trough below and drains to a separate container.

Material
High-density Australian wool felt
Diameter
Ø32 or Ø50 mm
A bag of wool felt discs, the rings each roller is built from

05 / 05

Adjustable mounting feet

Slotted brackets line the head up with the strip path and the feed height of your line.

Adjustment
Slotted brackets
Body
Aluminium alloy
Slotted mounting bracket at the end of the roller head
Front view of the CT roller head with six numbered points

The roller head, point by point

  1. Oil inletThe hose from the reservoir connects here.
  2. Adjustable oil guide tubesOne at each end of the head.
  3. Adjustable drip nozzlesTurn each brass valve to set how much oil drips.
  4. Felt rollersUpper and lower rollers coat both faces of the strip.
  5. Oil outletCollects the excess oil and leads it to a container.
  6. Adjustable fixing bracketsSlotted and bolted, to set height and position.

Still oiling the strip
the old way?

Pick what your line does today.

CT Stock Oiler

Mounted between the feeder and the die. Both felts oil the strip as it feeds, stroke after stroke.

  • CT oiler: yes.Oil on both facesOil bath: yes.
  • CT oiler: yes.Thin film, set by brass valvesOil bath: no.
  • CT oiler: yes.Strip leaves wetted, not soakedOil bath: no.
  • CT oiler: yes.Oil only where the strip needs itOil bath: no.
  • CT oiler: yes.Runs from a 4 L reservoirOil bath: no.
  • CT oiler: yes.Oil kept covered and filteredOil bath: no.

Oil bath

The strip leaves the tray soaked. The die needs a thin film; the rest drips off along the line, onto parts, tooling and the floor.

Tell us how you oil today

Any strip.
The roller to match.

Wool felt rollers under the brass drip valves

Wool felt roller Ø32

Ø32 mmRoller diameter
Up to 3 mmMaterial thickness
1 spare setFelt discs included

The standard surface for double-sided strip lubrication in general stamping.

Ask for this roller

Pick your size in two steps

Strip width picks the model. Strip thickness picks the roller.

Step 1

By strip width

The CT number is the working width in millimetres. Take your widest strip and choose the model at or just above it.

Strip 280 mm wide
CT300
Strip 600 mm wide
CT600

Step 2

By strip thickness

Thicker strip takes the larger felt roller.

Up to 3 mm
Ø32 felt roller
Up to 6 mm
Ø50 felt roller
Over 6 mm
Send us your material

Delivery

Standard models ship within 2 days

All 20 CT widths are kept in stock in Dongguan, with one spare set of felt discs in the box.

Send your strip width

20 models. The number is the working width.

  • CT6565 mm
  • CT100100 mm
  • CT150150 mm
  • CT200200 mm
  • CT250250 mm
  • CT300300 mm
  • CT350350 mm
  • CT400400 mm
  • CT450450 mm
  • CT500500 mm
  • CT550550 mm
  • CT600600 mm
  • CT650650 mm
  • CT700700 mm
  • CT800800 mm
  • CT900900 mm
  • CT10001000 mm
  • CT12001200 mm
  • CT13001300 mm
  • CT1M61600 mm

A CT300 gives 300 mm of felt contact. Pick a head at least as wide as your widest strip. Working width is the usable felt length, not the overall frame length; mounting dimensions are confirmed with your order.

One roller head.
Two ways to feed the oil.

CT Gravity

The standard kit. A hanging reservoir drips oil onto the felt rollers. Nothing to wire and nothing to plumb.

The CT gravity kit: roller head, 4 L reservoir, ball valve and hose

No pump. No power.

Standard supply

Oil supply

  • 4 L transparent hanging reservoir with a built-in filter screen
  • Oil flows by gravity through a ball valve and a PVC hose
  • Brass micro-adjustment valves along the roller width
  • Excess oil drains from the lower trough to a separate container

Control

  • Set by hand: open the valves over the sections that need oil
  • No wiring and no signal from the press

Rollers

SurfaceDiameterMaterial thickness
Wool feltØ32 mmUp to 3 mm
Wool feltØ50 mmUp to 6 mm
Wool feltØ22 mmOption, confirmed by HENLI
NBR rubberOn requestAluminium and copper strip

Power and air

  • No electrical power
  • No compressed air

Size

  • Working width 65 to 1600 mm, 20 models
  • The standard head is 100 mm longer overall than its working width
  • Aluminium alloy body

Delivery

  • All CT models are kept in stock
  • Ships within 2 days of receiving payment
  • One spare set of wool felt discs included

CT + Pneumatic Tank

An option for the same roller head. A 20 L tank beside the press feeds the oil automatically and takes the excess back.

Pneumatic recirculating oil tank with a roller head mounted in front

Automatic, with oil return.

Option: add the tank

Oil supply

  • 20 L tank standing beside the press
  • An air-driven pump feeds the roller head through one hose
  • A second hose returns the excess oil to the same tank through a filter
  • Low-oil buzzer alerts the operator

Control

  • Timed oiling, set in hours, minutes or seconds
  • Press-signal oiling, synchronized with the press cam signal
  • Jog feed button to wet the rollers before production

Rollers

SurfaceDiameterMaterial thickness
Absorbent fiberØ70 mm0.1 to 3.0 mm
Wool feltØ32 mmUp to 3 mm
Wool feltØ50 mmUp to 6 mm

Power and air

  • Control power 24 V DC, 3 W
  • Air pressure 0.1 to 0.8 MPa

Size

  • Tank 400 × 300 × 200 mm
  • Overall 400 × 300 × 450 mm
  • Same CT heads, working width 65 to 1600 mm

Typical use

  • High-speed stamping of terminals and connectors on copper strip
  • Where a thin, even film is needed without spray mist

How to use it, in 45 seconds

Mount it, hang the bottle, set the valves, run the strip.

Pneumatic recirculating oil tank

For lines that want the oiling automatic, with the excess oil returned.

Pneumatic oil tank with a roller head in front of it, standing on the workshop floor

A 20 L tank beside the press

An air-driven pump feeds the roller head through one hose. A second hose returns the excess oil to the same tank through a filter. A buzzer warns when the oil is low.

  • Tank 400 × 300 × 200 mm, overall 400 × 300 × 450 mm
  • Air pressure 0.1 to 0.8 MPa
  • Control power 24 V DC, 3 W
  • Same CT heads, working width 65 to 1600 mm
Tank controller with a digital timer, a green button and a red button

Timed, or triggered by the press

Set the oiling by time, in hours, minutes or seconds, or let the press cam signal trigger it. A jog button wets the rollers before production.

  • Used for high-speed stamping of terminals and connectors on copper strip
  • A thin, even film without spray mist
  • Rollers: absorbent fiber Ø70 mm, or wool felt Ø32 and Ø50 mm
Ask about the tank

Cut sheets or round blanks?
There is a sheet oiler for that.

The CT oils continuous coil strip. The DSO oils one cut piece at a time.

DSO sheet oiler with a round blank lying on its roller table

DSO double-sided sheet metal oiler

A roller table that stands in front of the press. It oils both faces of each cut blank, then returns the blank to the side it came from, so one operator loads and collects from the same place.

  • Working widths 300, 500, 600 and 1200 mm
  • Photoelectric sensors detect the blank
  • Handwheels set the roller gap for the blank thickness
  • 15-day lead time, 2-year warranty
Ask about the sheet oiler
  • A round blank entering the oiling rollers

    Place the blank

    Lay it on the table. A photo sensor sees it and the rollers take over.

  • Close view of the oiling head and drive rollers

    Coat and return

    Upper and lower rollers coat both faces. At the far sensor the feed reverses.

  • Sheet oiler running in the workshop with a round blank on the table

    Collect and form

    Pick up the oiled blank and place it in the die for one stroke.

Tell us your strip width.
Get a quote today.

Get a quote

On the shelf in Dongguan

All CT models and mounting accessories are kept in stock, so an order does not wait for production. Oilers ship within 2 days of receiving payment.

Ask for your width
Finished CT roller heads of different widths standing on a shelf

Where press shops
mount the oiler

  • CT oiler mounted on a press with the reservoir hanging above it

    On the press

    Reservoir above, head in the strip path

    The light aluminium head mounts before the die on new lines and retrofits.

  • CT oiler set beside the die

    At the die

    Set right beside the die

    Check the clearance in front of the die and the fixing points for the brackets.

  • Punched strip leaving the felt rollers

    Punched strip

    Strip leaving the felts

    Both faces carry the film by roller contact. Nothing is sprayed.

  • Roller head installed on a running strip line

    Running line

    On a running strip line

    The same head works with gravity supply or with an automatic tank.

  • Bright metal strip passing under the row of brass drip valves

    Drip valves

    Oil only where the strip runs

    Each brass valve meters the oil for its own section of the roller width.

  • Slotted mounting bracket at the end of the roller head

    Brackets

    Slotted brackets set the feed height

    Send a photo of your machine and we advise on the mounting.

Fits the machines you already run: punch presses and stamping lines, NC servo feeders, pneumatic and roller feeders, coil straighteners, 3-in-1 uncoiler-straightener-feeders and roll-forming lines.

Reservoir, roller head and a bag of spare felt discs laid out together

Spare felt in every box

Every wool felt oiler ships with one extra full set of felt discs at no extra charge, matched to your roller size and width.

  • Roller head with felt fitted
  • 4 L reservoir, ball valve and hose
  • Adjustable mounting brackets
  • One spare set of wool felt discs
Ask what ships with your model
Racks of felt, rubber and fiber rollers in the HENLI parts store

Built in Dongguan since 2003

HENLI is the brand of Dongguan Xinxiang Machinery Equipment Co., Ltd. The rollers, heads and tanks are made in our own factory, so you buy from the maker.

Contact the factory

Questions buyers ask

What is a stock oiler, and what else is it called?

A stock oiler is a press-line accessory that puts a thin, controlled oil film on both faces of the material before the die. Buyers also call it a stock lubricator, strip lubricator, stamping oiler, roller lubricator, felt roller lubricator, oil coating machine or punch press oil feeder.

How does the lower felt roller get its oil?

The manifold drips oil onto the upper felt roller. The oil runs down and wets the lower felt, so both rollers coat the strip.

How do I choose between gravity and the pneumatic tank?

Gravity supply is a simple drip system that you adjust by hand. Choose the pneumatic tank when you want timed or press-signal oiling and the excess oil returned to the tank.

Does the collected oil go back to the hanging bottle?

No. On the gravity kit the excess oil drains into a separate container and can be returned by hand after checking. The pneumatic tank returns it automatically through its own hose.

Which oils can the rollers use?

Common stamping and drawing lubricants, including vanishing oils, mineral oils and synthetic blends. Tell us the oil when you order. Highly corrosive or acidic oils are not suitable for the absorbent fiber sleeves.

Why is the oil coating uneven?

Check that the strip runs inside the felt width and that the head is level with the feed height. Wet both rollers before production, then open the brass valves over any dry section. Look for metal debris or damage in the felt.

Can it handle material thicker than 6 mm?

Standard felt heads cover material up to 6 mm. For thicker material send the material, width, thickness and feed speed, and HENLI confirms a roller and oil supply for your line.

What decides the price?

The working width, the roller head, the oil supply, the control voltage and the quantity.

Discuss your strip
and your press

Send four facts: material, widest strip, thickness range, press and feeder type. A photo helps.